English 
T: +86-571-8663-6649
E: hzbjys@hzbjys.com
E: hzbjys@hzbjys.com
7/F, 1st Building Of ZhongHao WangJiang International Center, NO.332 East WangJiang Road, HangZhou, ZheJiang, China.
| Quantity: | |
|---|---|
Product Description
Brass sheet represents a copper-zinc alloy flat product manufactured through rolling processes. This product category covers multiple alloy grades including C2720, C2700, C2680, C2600, and C2300, each formulated with specific zinc content ratios to match different forming and strength requirements. Produced with thickness ranging from 0.1mm-0.2mm, these brass sheets serve as raw material for stamping, etching, and decorative fabrication processes across industrial and architectural sectors.
The manufacturing facility operates with 28 years of experience in non-ferrous metal production. Production follows established rolling and annealing procedures, with each batch documented through material test reports. Sheet surfaces undergo visual inspection before packaging to ensure consistent finish quality across ordered quantities.
Parameter | Specification Range |
|---|---|
Alloy Grade | C2720, C2700, C2680, C2600, C2300 |
Temper | O, 1/4H, 1/2H, H |
Thickness | 0.1mm-0.2mm |
Width | 10mm-400mm |
Length | 30mm-6000mm |
Surface Finish | Bright and smooth |
Form | Flat sheet |
Application Category | Industrial components, decorative elements |
Custom dimensions outside standard ranges can be discussed for volume orders. Tolerance levels conform to the standards listed in the compliance section below.
Production adheres to multiple international and regional standards, enabling compatibility with procurement specifications across different markets:
GB/T 4423-2007 (China national standard for copper and copper alloy bars)
JIS H3250-2006 (Japanese Industrial Standard for copper and copper alloy sheets)
EN 12163-1998 (European standard for copper and copper alloy rod and bar)
ASTM B150M-03 (Standard specification for copper alloy strip)
ASTM B98M-03 (Standard specification for copper-zinc alloy sheet and strip)
ASTM B151M-05 (Standard specification for copper-nickel-zinc alloy sheet and strip)
Each production batch receives a material test report documenting chemical composition and mechanical property verification. Clients may request third-party inspection arrangements for large-volume orders.
Brass sheets in this thickness range exhibit specific material properties relevant to fabrication processes:
Formability: O temper material supports deep drawing and complex bending operations. Hard tempers (1/2H, H) provide increased tensile strength for structural components requiring dimensional stability.
Surface quality: Bright finish sheets maintain uniform reflectivity suitable for decorative panel applications and visible architectural elements. Smooth surface condition also supports subsequent plating, etching, or lacquer coating processes.
Corrosion behavior: Copper-zinc alloys demonstrate resistance to atmospheric exposure and indoor moisture conditions. For outdoor coastal installations, additional surface treatment may be specified during the quotation phase.
Machinability: Brass alloys respond well to stamping, blanking, and laser cutting operations commonly used in component manufacturing workflows.
These brass sheets find use across several commercial and industrial segments:
Architectural decoration: Wall cladding panels, ceiling inlays, door trim elements, and ornamental metalwork for commercial buildings and hospitality interiors.
Electrical components: Terminal connectors, grounding strips, and conductive shims where copper-zinc conductivity meets application requirements.
Hardware manufacturing: Locks, hinges, decorative fixtures, and furniture hardware produced through stamping and forming operations.
Signage and nameplates: Engraved or chemically etched identification plates, directional signs, and brand markers for industrial facilities and commercial premises.
Heat exchanger elements: Selected alloy grades serve in low-temperature heat transfer applications within HVAC and process equipment.
Order minimums: Production orders require 2500 kilograms minimum quantity. Stock items may be available from 300 kilograms depending on current inventory status.
Packaging: Sheets are separated with protective paper interleaving and packed onto export-grade wooden pallets. Edge protection is applied to prevent transit damage. Packaging dimensions and weight are confirmed prior to shipment.
Customization: OEM specifications including custom dimensions, special tempers, or branded packaging can be accommodated for volume orders. Sample orders are accepted for material evaluation purposes.
Lead time: Stock items typically ship within 3-7 working days. Custom production orders require 15-25 working days depending on alloy and quantity.
Payment terms: Telegraphic transfer (T/T) and letter of credit (L/C) are accepted for commercial procurement transactions.
For deep drawing or complex forming operations, O temper (fully annealed) material provides maximum ductility. For shallow stamping where dimensional rigidity is also required, 1/4H or 1/2H tempers may be appropriate. Our technical team can review your part drawings to recommend the matching temper grade.
Standard production delivers bright and smooth finish as listed. Custom surface treatments including brushed, mirror polished, or satin finishes can be arranged for dedicated production orders. Please specify surface requirements during the inquiry stage for accurate quotation.
Each delivery includes a material test report covering chemical composition verification and mechanical property data as applicable. Additional documentation such as certificates of origin, inspection reports, or customs paperwork can be arranged according to destination country import requirements.
